imported>NelsonJenkins |
imported>NelsonJenkins |
Line 1: |
Line 1: |
− | The '''Security Camera Kit''' is a package of three HUD-controlled security cameras with a controller desk for selective access made by [[Gentek]].
| + | #REDIRECT [[NTBI Group]] |
− | | |
− | | |
− | ==Setup==
| |
− | The cameras can be set up in a matter of seconds. '''NOTE: Do not rez cameras within 3 seconds of each other - this is to allow them time to detect other cameras and avoid naming conflicts.'''
| |
− | # Rez your chosen camera and position/rotate it to your liking. ''For the Dome model, click it and select "Mount Opts" to change the mounting bracket. A corner-mount is available, as well as no bracket for roof/overhang mounting.''
| |
− | # The camera will automatically name itself; however, if you wish to name your cameras and group them together, click it and select "Set ID" and "Set Group". See below for an explanation of IDs and Groups.
| |
− | # Repeat steps 1 & 2 for each camera you want. (Cameras can be added/removed later.)
| |
− | # Rez the Security Camera Desk and open the _access notecard inside it. Read the instructions at the top to set your access settings. Save & close the notecard.
| |
− | That's it - you can now test out your cameras.
| |
− | | |
− | [[File:Camhud-diagram.jpg|frame|left|caption]]
| |
− | ==Using the System==
| |
− | Just sit on the desk and accept the attachment permissions. The HUD will automatically attach, and then you can browse between cameras.
| |
− | | |
− | ==Camera HUD==
| |
− | # '''Exit''' - Removes the HUD and stands you up. '''''Always'' use the X button to end your session!''' Otherwise, the camera you were viewing may not be reset properly.
| |
− | # '''Sorting Options''' - ''Sort by group'' separates cameras into their groups, while ''Sort by name'' sorts all cameras alphabetically without group designations.
| |
− | # '''Group Header''' - Identifies a camera group. Group headers aren't clickable.
| |
− | # '''Type Icon''' - Identifies the type of camera, e.g. box (shown), dome (below), and interior (not shown).
| |
− | # '''Camera ID''' - The ID of the camera. Click this (or the Type Icon) to select/deselect that camera.
| |
− | # '''Scroll Buttons''' - Scrolls between pages, if there are more than 20 cameras.
| |
− | # '''Save Rotation''' - Saves the current camera rotation as the default rotation.
| |
− | # '''Recall Rotation''' - Recalls the default rotation. This is also done when the camera is deselected.
| |
− | '''''NOTE:''' The HUD cannot be used by manually attaching it; it must be rezzed and auto attached from the desk.
| |
− | | |
− | ==Troubleshooting==
| |
− | * I can't sit on the desk.
| |
− | ** Make sure you have access to it (the owner is always given access, but other users must be added to the access list).
| |
− | ** There may be an error that's causing you to be kicked off; check local chat for a notification.
| |
− | * The HUD is not showing up, or "Unable to rez HUD."
| |
− | ** You must accept the attachment permissions request for the HUD to attach. Check your notification bar.
| |
− | ** The desk must have permissions to rez on the parcel - check to make sure rezzing is enabled. If it is restricted to the land group, you must set the desk to the land group.
| |
− | ** The parcel may be full - the HUD requires 43 available prims to rez.
| |
− | * "A duplicate camera ID was detected" or "Camera ID already in use - please change ID to something else."
| |
− | ** The system won't work if two cameras have the same ID, even if they are in separate groups. Change the ID of the camera.
| |
− | ** You may have rezzed two cameras within 3 seconds of each other, and their IDs are identical - don't do this.
| |
− | * The HUD just shows "Initializing..." and there is no error message.
| |
− | ** In laggy sims, this may take more than a few seconds.
| |
− | ** Make sure scripts are enabled on the parcel.
| |
− | * "WARNING: linkNum returned 0 for camera link. Camera will not work."
| |
− | ** The camera was unlinked. Re-link the camera together.
| |